Featured Post

October 2 - Meetings, Grading and Pews

Image
Another Status Meeting in the Church - A week ago Sunday the second status update meeting was held at the church. While there were some assembled pews, they were all in the sanctuary, and not in the dining hall where the meeting convened. So, everyone that wanted to sit had to bring their own chair. In the picture, Bob is standing but not because he failed to bring a chair. He wanted attention so he stood up in the front to give his status update. After Sam reported on the finances discussion ensued about whether or not to increase our self imposed debt ceiling. While the church could be 'completed' without the increase, some desired items like an epoxy sealed kitchen floor would have to be deferred. The congregation agreed to up the debt limit. Sam stated that the bank is fine with the new debt ceiling. Sam also said the projection stand in the picture is only temporary. With the current projected spending, we will still not have a completed kitchen so the eagle-eyed shoppers ...
Post a Comment

July 15 - Picking Rocks, Mudding the Walls and Mystical Fire Shutters

Tuesday Was Rock Picking Day -
A family oriented event, rock picking brings out folks of all ages, but especially the younger end. Larger rocks that would likely cause the mowers grief are hand picked from the area that will soon be grass. Farmer Paul drives the tractor and the multitudes fill the trailer with rocks. I did not get a picture, but I did see that when the multitude needs a lift, they all pile on the trailer.

On arrival Tuesday evening I was surprised to see the still-gravel lot with yellow lines demarcating parking spaces. I figured that paving generally precedes striping, but maybe that just continues to reveal my ignorance of construction. I do wonder what will happen to the stripes in a sand lot when the rain descends and the floods come. We will see when the time comes.


Taping and Mudding -
When I walk into a building with painted walls, I might admire the finish on the walls but I have never stopped to consider how many sheets of drywall were used, how many screws were needed to hang them or how many feet (miles?) of drywall seam need to be taped and mudded over. Our church is not a large structure, but just out of curiosity, we did a few calculations. We figure that there is about three quarters of an acre (about 30,000 square feet) of drywall on the walls and ceilings. There may be about 35,000 screws used to secure it, give or take a few handfuls. And possibly 4 miles of seam to be taped. I can't attest to the accuracy of all the numbers, worked out before the coffee got cold, but I was curious. I do know that there have been some experienced folks working many hours first applying the tape, then second and third layers of mud (maybe more accurately 'taping compound' but I prefer mud).
Here Dave is on the lift to better reach the high spots.

Dave teams up with Phil and the laser to get a corner joint straight  and plumb.

Phil finished off a window opening in the kitchen.

Phil mixes another batch of mud.

Just a little stiff, so add a couple of spongefuls of water.

Ah, just right.

Matt also does a lot of taping and mudding. I think I heard him say "Really, Ed, the lunker was at least this big!", but maybe my hearing aid was low on battery.


Fire Shutters -
The fire wall separating the sanctuary from the narthex has size large windows. So, in order to maintain its status as a fire wall, it has to have fire shutters. I will admit, I have never previously heard of fire shutters. But now I have watched one be installed and have photographic evidence of three such devices. so I am probably a near expert on the subject at this point.

Ami uses the laser to get the steel side rail assembly vertical. This is important since the shutter relies on gravity to be deployed into proper position so we dare not have it bind on an out-of-plumb rail.

The same approach on the other side.

Next affix the ends to the spring loaded spool. This is heavy stuff so a size pretty big lift is used to raise the spool and the shutter.

Turn the crank and winch up the load.

When it is properly positioned, put the bolts through the holes in the end brackets and the side rails.
Again using the lift, raise the shutter into position and affix it to the spool. It looks like the hardware is all factory aligned so it goes together quite nicely, but I do not think I will try this trick at home.
When it is all installed, it looks like this one in the narthex.
I think Ami has done this before. He did not spend a lot of time staring at the instruction manual.

In the event of a fire, this 165 degree fuse will melt, the restraining cable or chain will then be free, the shutter will surrender to gravity and close down. The system is to be tested at least once per year to make sure that it is operational. The fire wall with this shutter setup essentially separated the structure into two buildings with a two hour fire rating, meaning that it should take at least two hours for a fire to spread from one side of the building to the other. While these precautions seem good and necessary, I pray that we never have to have a real life test of the fire wall and it shutters.

Comments

Post a Comment

Popular Posts

February 17 - Pouring the Floor, Part 2

Image
Pouring it On Sweatshirts and jackets came off as the morning wore on, the temperature rose, and that heavy concrete hose was dragged all over the church.  When I returned to the church at about 11:30 that morning, I saw the last of the concrete truck parade.  One truck was emptying its load, another was cleaning up, and a third was pulling away to return to home base. Inside was a surprise -- the floor was almost finished!  The last of the narthex, office, coat room, and mechanical room was being poured.  Here you can see the power screeding machine in action again.  The reference laser it uses can be seen in the distance, fastened high on the door jamb leading to the sanctuary, visible just above Brian's head. By now, everyone seemed to know exactly what to do and when to do it. The pump outside is controlled remotely by Jeff Wikman, via the yellow control box he's holding.  While Mark directs the hose, Jeff monitors the progress, ready to stop the pump i...
Read more

October 2 - Meetings, Grading and Pews

Image
Another Status Meeting in the Church - A week ago Sunday the second status update meeting was held at the church. While there were some assembled pews, they were all in the sanctuary, and not in the dining hall where the meeting convened. So, everyone that wanted to sit had to bring their own chair. In the picture, Bob is standing but not because he failed to bring a chair. He wanted attention so he stood up in the front to give his status update. After Sam reported on the finances discussion ensued about whether or not to increase our self imposed debt ceiling. While the church could be 'completed' without the increase, some desired items like an epoxy sealed kitchen floor would have to be deferred. The congregation agreed to up the debt limit. Sam stated that the bank is fine with the new debt ceiling. Sam also said the projection stand in the picture is only temporary. With the current projected spending, we will still not have a completed kitchen so the eagle-eyed shoppers ...
Read more

September 25 - Last Saturday: A Really Big Day

Image
Concrete Pour -  Another concrete pour, this time the sidewalks across the front and the walk under the portico. Two truckloads of mud got all the sidewalk done and half of the dumpster pad beyond the back edge of the parking lot. Sonny Johnson, Phil Johnson and Charlie Halonen from the Minneapolis congregation as well as Dale Muhonen from Rockford volunteered to help with the job. Once again, a helping hand from the neighboring congregations is greatly appreciated. It is always fascinating to watch this work - when the truck is spilling its contents, many hands and feet are required to coax the heavy goo into its desired location. Phil is shown pushing the goo around while Sonny and Dale operate the screed. After the concrete is leveled out, the bull float is used to smooth the surface. The float may reveal a spot lacking just a little material so the master adds a shovelful here and there to make sure the surface is just right. After the mix has a chance to set up a bit, the red ...
Read more